Before you blame the transfer, check these five things. The problem might be sitting right on your heat press.
You lined up your design perfectly. The heat press beeped. You lifted the platen, started peeling the film, and… part of your beautiful design came right back up with it.
There goes another shirt. Another transfer. And possibly a few words you wouldn't say in front of your grandmother.
Sound familiar?
The good news is that a DTF transfer that won't stick doesn't automatically mean you received a bad transfer. Sometimes the problem is your press, your garment, or one small step in your application process.
Here's what to check before sacrificing another perfectly good T-shirt.
DTF25's published pressing settings
300°F · 10–15 seconds · medium pressure · cold peel.
These settings are for DTF25 transfers. Follow the complete instructions supplied with your order, including the second press. DTF25's refund policy specifically says not to skip or shorten it. If you need the second-press timing for your order, contact the shop before pressing your batch.

1. Your heat press might be lying to you
Just because the display says your press is at the right temperature doesn't mean every inch of the heating platen actually is.
Some presses develop cold spots. Others lose heat during continuous production.
Try this: Verify your press temperature with a suitable contact probe or temperature-testing strips. Check several locations, particularly if failures consistently happen in the same area.
Don't automatically crank up the temperature. You could scorch your garment without fixing the underlying problem.
A test shirt might cost you a few dollars. Fifty ruined shirts could cost you a customer.
2. You're pressing the design, but not evenly
Here's something that catches people off guard: your heat press can close completely and still fail to apply uniform pressure.
Thick collars, seams, pockets, and zippers can prevent the platen from making even contact with the transfer.
Try this: Move bulky seams outside the pressing area whenever possible. Use an appropriate firm application pad or compatible platen when needed, and adjust the pressure with the garment and accessories in place.
3. You skipped the pre-press
Fabric can hold moisture, even when it feels dry. That moisture, along with wrinkles, can interfere with a consistent application.
Try this: Pre-press the garment briefly when recommended for your fabric and transfer. STAHLS suggests approximately 3–5 seconds for many standard garments, with additional caution for heat-sensitive materials.
4. You're peeling at the wrong time
Not all DTF transfers use the same peel instructions. Some are designed for hot peeling. Others require cooling before the carrier is removed.
Try this: Check the specific instructions that came with your transfers. Don't assume the peel method from your last supplier applies to the next one.
If the design starts lifting with the film, stop and reassess rather than pulling harder.
5. You didn't follow the complete application instructions
Temperature gets most of the attention, but time and pressure matter just as much. A transfer may initially appear attached yet fail later if the adhesive wasn't properly bonded.
Your garment fabric and the supplier's instructions also matter.
Try this: Before pressing another shirt, confirm the prescribed temperature, pressing time, pressure, peel method, and whether a finishing press is required. Don't treat settings from another transfer brand as interchangeable.
The DTF25 save-your-shirt checklist
Before your next press:
- Confirm the transfer's application instructions.
- Verify press temperature and recovery.
- Remove seams and obstructions from the pressing area.
- Pre-press the garment when appropriate.
- Use the specified pressure, time, and peel method.
- Test one sample before running the entire order.
One last thing: don't gamble with a 50-shirt order
A test shirt might cost you a few dollars. Fifty ruined shirts could cost you a customer.
Take the extra time to verify your process, especially when working with a new fabric, transfer supplier, or heat press.
And if you've checked everything and the problem continues, document the failure and contact your supplier. Include photographs, garment composition, application settings, and the results of your tests.
Great printing isn't about getting lucky. It's about getting consistent.
DTF25 — Helping you print smarter, waste less, and keep your customers coming back.
Illustrations are original AI-generated visuals for DTF25, not actual adhesion-test photographs. Technical reference: STAHLS' Heat Press Application 101.